How do you really feel on the subject of How to Install a Bathtub Yourself?
Mounting a bath tub isn't exactly rocket science, however it does need solid plumbing, carpentry, and often, tiling skills. Changing an old bath tub with a new one is also a reasonably hard task. If the old bathtub is easily easily accessible, the task can move easily; if you have to open a wall to eliminate the old tub and place the brand-new bath tub, the job is a lot harder. In either case, the job is within a house handyman's skills, although you will need a helper to move out the old tub and set in the brand-new one. See to it you have actually certified yourself for the job and fit trying it. Instead of employing a specialist to take over a halfway-completed job, it is better to think about employing one before you start. Possibilities are you may require a specialist plumber to make tube links.
This short article will help you install a new bathtub in your shower room if you have actually currently bought a brand-new tub and do not need to transform the plan of your previous water supply pipes.
Your tools as well as material checklist must consist of the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water system. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be fairly problematic as a result of the limited access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a cloth ready for the remaining water that will originate from the pipelines. As soon as the supply pipes have actually been eliminated, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing compound.
Prior to moving on to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washing machines are in place between the tap as well as the sink. Protect the tap in place with the maker supplied backnut. When the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind needs to be linked to the tap finishes initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the called for placement. The wood boards are valuable in equally spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four little points.
The next goal is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the tub until the spirit level reviews degree.
To set up faucets, fit the bottom of the outermost adaptable tap adapter to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Switch on the water supply and also inspect all joints and also new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally check the overflow outlet and the regular electrical outlet for leaks.
Lastly, repair the bath paneling as described in the producer's instruction manual. Tiling and securing around the bath tub must wait till the tub has actually been used a minimum of when as this will certainly settle it right into its last position.
Getting ready for the Installment
First of all, the sustaining structure provided with the bathroom should be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two faucets using 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you make use of every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to now be ready to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath fulfills the floor tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, resulting in problems with dampness and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to allow for the motion experienced when the bathtub is in usage. The sealer can split relatively early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently offered on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or waterproof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very enthusiastic about Installing A Bathtub and I hope you appreciated my entry. Enjoyed reading our article? Please share it. Help another person discover it. I truly appreciate reading our article about Installing A Bathtub.
Reliable? That's us!